UbuntuNetworking: Difference between revisions
From KVM
m (Bsd moved page AnthonyLiguori/Networking to UbuntuNetworking without leaving a redirect: Moved to more relevant heading) |
|||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
= Setting up NAT with KVM in Ubuntu = | = Setting up NAT with KVM in Ubuntu = | ||
Normally, the best way to do guest networking is by setting up a bridge. However, if you use a wireless card, are frequently switching network interfaces or using VPN, or for other reason want to do NAT, then this outlines the easiest way to set it up with Ubuntu. The setup here is very similar to what [http://www.libvirt.org libvirt] uses for QEMU networking. | Normally, the best way to do guest networking is by setting up a bridge. However, if you use a wireless card, are frequently switching network interfaces or using VPN, or for other reason want to do NAT, then this outlines the easiest way to set it up with Ubuntu. The setup here is very similar to what [http://www.libvirt.org libvirt] uses for QEMU networking. | ||
| Line 5: | Line 5: | ||
== Install Dependencies == | == Install Dependencies == | ||
sudo apt-get install bridge-utils dnsmasq | sudo apt-get install bridge-utils dnsmasq | ||
== Check Kernel Modules == | == Check Kernel Modules == | ||
Make sure that all of the following modules are around: either built in to the kernel or loadable. If you are running a plain distribution kernel, you should have all of these around without doing anything extra. | Make sure that all of the following modules are around: either built in to the kernel or loadable. If you are running a plain distribution kernel, you should have all of these around without doing anything extra. | ||
# lsmod | # lsmod | ||
| Line 24: | Line 22: | ||
nf_conntrack_ipv4 21776 3 iptable_nat | nf_conntrack_ipv4 21776 3 iptable_nat | ||
nf_conntrack 76688 5 xt_state,ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4 | nf_conntrack 76688 5 xt_state,ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4 | ||
== Enabling ip forwarding == | == Enabling ip forwarding == | ||
| Line 33: | Line 30: | ||
== Configuring a bridge == | == Configuring a bridge == | ||
Add the following to the bottom of <code>/etc/network/interfaces | Add the following to the bottom of <code>/etc/network/interfaces</code> | ||
auto br0 | auto br0 | ||
| Line 45: | Line 41: | ||
bridge_ports none | bridge_ports none | ||
pre-up iptables-restore < /etc/iptables.up.rules | pre-up iptables-restore < /etc/iptables.up.rules | ||
== Installing config files == | == Installing config files == | ||
# Copy [[Media:dnsmasq.conf|dnsmasq.conf]] to <code>/ | # Copy [[Media:dnsmasq.conf|dnsmasq.conf]] to <code>/etc/dnsmasq.conf</code> | ||
# Copy [[Media:iptables.up.rules|iptables.up.rules]] to <code>/etc/iptables.up.rules</code> | # Copy [[Media:iptables.up.rules|iptables.up.rules]] to <code>/etc/iptables.up.rules</code> | ||
# Copy [[Media:qemu-ifup|qemu-ifup]] to <code>/etc/qemu-ifup</code> and change permissions to <code>755</code> | # Copy [[Media:qemu-ifup|qemu-ifup]] to <code>/etc/qemu-ifup</code> and change permissions to <code>755</code> | ||
Latest revision as of 15:34, 16 May 2015
Setting up NAT with KVM in Ubuntu
Normally, the best way to do guest networking is by setting up a bridge. However, if you use a wireless card, are frequently switching network interfaces or using VPN, or for other reason want to do NAT, then this outlines the easiest way to set it up with Ubuntu. The setup here is very similar to what libvirt uses for QEMU networking.
Install Dependencies
sudo apt-get install bridge-utils dnsmasq
Check Kernel Modules
Make sure that all of the following modules are around: either built in to the kernel or loadable. If you are running a plain distribution kernel, you should have all of these around without doing anything extra.
# lsmod Module Size Used by tun 15616 0 bridge 64104 0 llc 11504 1 bridge xt_state 5248 1 ipt_MASQUERADE 6720 1 iptable_nat 10512 1 nf_nat 24344 2 ipt_MASQUERADE,iptable_nat nf_conntrack_ipv4 21776 3 iptable_nat nf_conntrack 76688 5 xt_state,ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
Enabling ip forwarding
Add the following line to the bottom of /etc/sysctl.conf
net.ipv4.ip_forward=1
Configuring a bridge
Add the following to the bottom of /etc/network/interfaces
auto br0
iface br0 inet static
address 10.0.1.1
netmask 255.255.255.0
network 10.0.1.0
bridge_stp off
bridge_maxwait 5
bridge_ports none
pre-up iptables-restore < /etc/iptables.up.rules
Installing config files
- Copy dnsmasq.conf to
/etc/dnsmasq.conf
- Copy iptables.up.rules to
/etc/iptables.up.rules
- Copy qemu-ifup to
/etc/qemu-ifup and change permissions to 755